Nabtesco RV N Series Operation Manual Download | Manualshive

Page: 17 / 62

background image

Chapter 4 Preparations for Installation

9

4.2.2. Flange and its installation components



Motor mounting flange

• Prepare the motor mounting flange for fixing the motor on the reduction gear input side.

• In order to avoid contact with reduction gear components, refer to the sizes indicated in the “External

dimensions” drawings when designing the motor mounting flange.

• Confirm that a tapped hole for injecting/draining grease is installed in the motor mounting flange. It will be

necessary for filling or replacing the lubricant after installing the reduction gear.

• Design the motor mounting flange to the following accuracy. If the installation accuracy is poor, it will result

in vibration, noise, and increase in backlash. If a model other than those listed below is used, refer to our
contact information.

<Installation accuracy>

Table 4-1

Fig. 4-2

Model

Concentricity

tolerance

Motor mounting
flange

Model

Concentricity

tolerance

«
...
15
16
17
18
19
...
»

Summary of Contents for RV N Series































































Reviews:

No comments

Related manuals for RV N Series

Brand: UnionSpecial Pages: 56

Brand: Falcon Pages: 52

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Movie FL Black E27 Flaps

Brand: Qazqa Pages: 2

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Federal Pages: 43

Brand: Dana Design Pages: 20

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: h/p/cosmos Pages: 81

Brand: Keithley Pages: 79

Brand: Kayakpro Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands