MYERS MP Series Operating Manual Download Page 71

Page: 71 / 169

MP SERIES™ Battery Backup System for Traffic Signals: MP2000E System

Volume One: Operating Manual

Page 6-23

6.b.11 MAINTENANCE Submenu

As this menu is normally used by trained and qualified

personnel ONLY, users have the option of creating a password

to access this menu. Instructions on password creation are

presented in Section 6.c.4.2.1.

The factory default password is 1111. If the password is lost

or forgotten, contact Myers EPS MP2000E Technical Support.

Figure 6-14 details the MAINTENANCE Submenu.

FUNCTION

LCD SHOWS

ACTION

PASSWORD

ACCESS

If the MAINTENANCE Menu has been

password protected, the password must

be entered here. Use the UP / DOWN

arrow key with ENTER keys to confirm a

correct Password. Reentry is required if

an error is made entering a password.

BATT TEST

OPTION

Battery Test Option can be verified here.

Battery Test period of 1 to 255 minutes

can be selected here in 1 minute

increments
The MP2000E can be tested to run on

battery for Maintenance purposes.

INV ON / OFF

Inverter can be turned ON or OFF. This

option is available ONLY when the

MP2000E is in BATTERY or STANDBY

Mode

EVENT LOG VIEW

The Event Log with Date & Time is

viewed here in Binary digital format. See

Section 6.b.14 for details

LINE

CONDITIONING

Allows setting of line detection

parameters.

Figure 6-14: Maintenance Submenu

Summary of Contents for MP Series










































































































































































Search results

Summary of Contents for MP Series

Reviews:

Related manuals for MP Series

Brands by name

Popular brands

MYERS MP Series, Operating Manual

Search results

Summary of Contents for MP Series

Reviews:

Related manuals for MP Series

Brands by name

Popular brands