MYERS MP Series Operating Manual Download Page 7

Page: 7 / 169

MP SERIES™ Battery Backup System for Traffic Signals: MP2000E System

Volume One: Operating Manual

Page vi

NPACKING

NSPECTION

HECKLIST



Carefully remove the MP2000E from the box and inspect the contents.

Verify that the box contains 1 MP2000E BBS System.

Verify that the box contains 1 temperature sensor probe cable with three-pin connector

Verify that the box contains 1 Operating Manual

Verify that the box contains 1 binder of Electrical/Mechanical Drawings

The Power Transfer Switch (PTS) and all the associated wiring & hardware required for

installation are supplied in a separate box.

The set of four (4) batteries may be shipped separately, if a large quantity of MP Series

systems is supplied.

AVE THE

RIGINAL

HIPPING

ATERIALS

When returning the MP2000E for servicing, use the original shipping box and Styrofoam

protectors. Myers Emergency Power Systems is not responsible for damage caused by

improper packaging of returned systems.

EAD THE

PERATING

ANUAL

Before installation, become familiar with the MP2000E by reviewing the procedures and

drawings in this manual. If you have any questions about safe installation, operation, or

maintenance, contact Myers Emergency Power Systems service department at 866-MY-

MYERS.

OTE

If any items are missing or damaged, contact

Myers Emergency Power

Systems

(610-868-3500) and the shipping company immediately.

Most shippers have a short claim period.

OMPLETE THE

ORMS

ELOW FOR

OUR

ECORDS

SSIST WITH

ERVICE

EQUESTS

Summary of Contents for MP Series










































































































































































Search results

Summary of Contents for MP Series

Reviews:

Related manuals for MP Series

Brands by name

Popular brands

MYERS MP Series, Operating Manual

Search results

Summary of Contents for MP Series

Reviews:

Related manuals for MP Series

Brands by name

Popular brands