manualshive.com logo in svg

MUTOH VJ-626UF, Operation Manual

Share
Download
MUTOH VJ-626UF Operation Manual Download Page 99

Flow of Daily Maintenance     99

3

Daily  Maintenance

This printer requires daily maintenance.
Follow the steps below to perform daily maintenance after you finish your printing for the day.

• “Perform Daily Maint.” is prompted on the operation panel after certain period of time from the previous daily 

maintenance.
Make sure to perform daily maintenance when prompted.

Flow of Daily Maintenance

Important!

If you perform printing all day without entering to sleep mode, make sure to perform daily maintenance once a day.

Failure to perform daily maintenance may affect print quality or result in damage to the printer.

To perform daily maintenance without entering to sleep mode, go to “Mnt.9: Daily Maint.” on the operation panel.

"Mnt. 9: Daily Maint." on page 85

"Clean daily maintenance parts" on page 109

Daily Maintenance

Prepare required items for Daily Maintenance

The printer automatically performs the Short cleaning

Clean the print head circumference

Moisten the surface of print head nozzles

Leave the printer in Sleep Mode

Clean the cleaning wiper and the circumference of the cap

Daily Maintenance completed !

Clean the UV Lamp

Summary of Contents for VJ-626UF

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands