MUTOH VJ-626UF Operation Manual Download Page 119

Page: 119 / 144

Replacing the cleaning wiper 119

The cleaning wiper is an essential part to make printing consistent. Please replace it periodically.

Replacing period:

• Approx. every six months

Replacing the cleaning wiper

Note

If a non-replaceable wiper is installed on your printer (as shown in the illustration left below), you cannot replace it by yourself.

• For replacement, contact your local Mutoh dealer.

Skin or eye contact with UV curable ink may cause skin inflammation or allergic reaction.

For this operation, be sure to wear the supplied gloves (or solvent resistant gloves) and goggles to prevent ink from contacting
with your eyes or skin.

Do not open or close the cover while you are off balance.

You may pinch your finger or get injured.

Replacing steps

[1]

Check that no object including a jig is loaded on the table.

[2]

Press the [Menu] key.

[3]

• Press the [ - ] key until “Menu 3: Maintenance >” appears.

• Press the [>] key.

[4]

• Press the [ - ] key until “Mnt.3: CR Maintenance” appears.

• Press the [Enter] key.

Non-replaceable wiper

Replaceable wiper

CAUTION

Set Media

Remove Media

Media Set

Low speed

Press!

Menu 3 :

Maintenance >

Mnt. 3 :

CR Maintenance

Summary of Contents for VJ-626UF

















































































































































Search results

Summary of Contents for VJ-626UF

Reviews:

Brands by name

Popular brands

MUTOH VJ-626UF, Operation Manual

Search results

Summary of Contents for VJ-626UF

Reviews:

Brands by name

Popular brands