MUTOH VJ-626UF Operation Manual Download Page 39

Page: 39 / 144

Nozzle check and cleaning 39

[8]

• Press the [ - ] key until “Menu2: Test Print >” appears.

• Press the [>] key.

[9]

• Press the [Enter] key.

• To select Nozzle Check B, press the [ - ] key to display “Nozzle Check

B”, then press the [Enter] key.

• Nozzle check patterns will be printed.

[10]

Check the nozzle check print.

• If parts of lines are missing or faint, go to

"Cleaning steps" on page 40

• If all lines are clearly printed, go to

"Starting printing" on page 41

• The figure below are examples of the Nozzle Check patterns.

• Nozzle Check B is printed on the partially colored background.

• The figure below is an example of the Nozzle Check B pattern. In this example, non-colored background area is

shown in gray.

Note

The printer information (date and time of printing, printer’s serial number, firmware version) is printed on the nozzle check pattern.

Menu2

Test

Print

Test2

Nozzle

Check

Test1

Nozzle

Check

4 Color

6 Color

Summary of Contents for VJ-626UF

















































































































































Search results

Summary of Contents for VJ-626UF

Reviews:

Brands by name

Popular brands

MUTOH VJ-626UF, Operation Manual

Search results

Summary of Contents for VJ-626UF

Reviews:

Brands by name

Popular brands