manualshive.com logo in svg

MUTOH VJ-626UF, Operation Manual

Share
Download
MUTOH VJ-626UF Operation Manual Download Page 83

Mnt. 3: CR Maintenance     83

Mnt. 3: CR Maintenance

Use this for replacing absorption material for the flushing box and cleaning 
wiper.

"Replacing absorption material for the flushing box" on page 116
"Replacing the cleaning wiper" on page 119

Submenus

Press the [Enter] key to replace the 
absorption material for the flushing box.

• The carriage moves to the center of the 

printer.

• The cleaning wiper moves upward.

After the replacement is complete, press 
the [Enter] key.

• The printer moves the carriage and the 

cleaning wiper back to each original 
position.

Mnt. 4: UV Scan

Performs further UV curing.
Use this when you want to promote ink curing by applying additional UV light.

Submenus

"UV Scan 1: Start" on page 84

"UV Scan 2: Scans" on page 84

"UV Scan 3: Post Cure" on page 84

Note

The range over which the UV scanning is executed will depend on the current settings for “Size” and “Location” in the “MediaSetting” User 

Type.

Mnt. 3 :   

CR Maintenance

CR Maint. : 

 

Start

CR Maint. : 

 

End

Mnt. 4 :   

UV Scan >

UV Scan1 : 

 

Start

UV Scan2 : 

 

Scans

UV Scan3 : 

 

Post Cure

Summary of Contents for VJ-626UF

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands