MUTOH VJ-626UF Operation Manual Download Page 95

Page: 95 / 144

Replacing ink cartridge 95

When a cartridge is out of ink, the error LED on the operation panel flashes with beep sounds.
The printer pauses printing. After replacing with the new ink cartridge, it resume printing.

Replacing ink cartridge

Steps

[1]

Press the [Enter] key.

• The buzzer stops.

• In the icons shown on the left, the Slot 4 and 6 cartridges need

replacing.

[2]

Make sure you agitate the ink cartridge after you unpack it.

• Turn the ink plug upward and wait for three seconds.

• Next, turn the ink plug downward and wait for three seconds.

• Repeat that 10 times.

Note

When replacing varnish ink, you do not have to agitate it.

[3]

Remove the empty ink cartridge and insert the new one.

• Make sure to match the ink cartridge color with the label of this

printer.

• The arrow should face up.

• Insert all the way to the end.

Important!

• Do not replace ink cartridge when the power of this printer is OFF.

Ink level cannot be detected correctly.

• If ink cartridge is moved from cold to warm place, leave it at least three hours.

Leave ink cartridges away from fire or high temperature objects.

It may cause fire.

Note

Sleep mode continues after stopping the buzzer.

Ink End

[ 4 6 ] Ink End

x 10

3 sec.

slot 6

WARNING

Summary of Contents for VJ-626UF

















































































































































Search results

Summary of Contents for VJ-626UF

Reviews:

Brands by name

Popular brands

MUTOH VJ-626UF, Operation Manual

Search results

Summary of Contents for VJ-626UF

Reviews:

Brands by name

Popular brands