Beyond the basics
2.66
Programming regular and database polling
Note:
To erase a programmable one-touch key, refer to page 2.71.
Note:
For database polling to work, three things must be true:
•
The remote fax must be a memory-equipped Muratec fax with a file stored
in its database memory and ready for polling.
•
The database file which you’re polling must exist on the remote fax.
•
You must know the one- or two-digit file number for each database file you
wish to poll.
Note:
You cannot program continuous polling into a programmable one-touch key.
For more information on continuous polling, see page 2.31.
To program a polling operation, whether regular or database, into a programmable
one-touch key:
1.
Change to the Fax mode then press
PROGRAM
,
C
, 1,
ENTER
. The display either
shows:
Select Program No.
73:No Number Stored
. . . or indicates a command already is programmed into this key.
If 73 is the key you want to program, skip to step 4. (However, our examples
from here will say “76” rather than “73.”
2.
Select the key in which you want to program a command or change a
previously stored command — if necessary, turn the fliptab to see it, as
described earlier — and then press it. Here, we’ve selected 76.
Select Program No.
76:No Number Stored
3.
If you change your mind and wish to select a different programmable one-
touch key, go back to step 2 before going on to step 4.
4.
Press
ENTER
. The display now shows either:
76:Fax Number
_
or
76:Fax Number
9-5557312_
5.
Use the numeric keypad to enter the number exactly as your machine should
dial it, including whatever codes your phone system may require. The number
can be up to 40 characters in length:
76:Fax Number
9-5550629_
Your display can show only 20 characters at a time. To view characters beyond
those 20 (such as with an international long-distance numbers), press
to
scroll leftward or
to scroll rightward.
Important:
Do not press
ENTER
.
Note:
If you make a mistake or want to erase characters entered in a previous
setting, press
CANCEL
to erase leftward. Or, if you want to change just
one character in the number, press
to move the cursor leftward, or
to move it rightward, to that character and press
CANCEL
to erase it.
Then re-enter until the number is just as you want it.
6.
Now, while you still can see the fax number on the display, press
COMMUNICATION OPTIONS
four times and then press
ENTER
.
The display shows:
Polling
File No. _
If you’re performing regular (not database) polling, press
ENTER
and skip to
step 8.
7.
Use the numeric keypad to enter the one- or two-digit identifier for each
database file you want to poll. You can specify up to 10 files; between the
entry of each new file, press
COMMUNICATION OPTIONS
to insert a comma
but do not insert a comma after the last file number.
For example, here, we’ve entered 2, 6,
COMMUNICATION OPTIONS
, 2, 7,
COMMUNICATION OPTIONS
, 2, 8,
COMMUNICATION OPTIONS
(the letter in
preparation for another file number):
Polling
File No. 6,27,28_
Note:
The display shows only seven characters of the file number.
Important:
Again, do not insert a comma after the last file number.
When the entry is complete, press
ENTER
.
8.
If you want the polling to begin immediately every time you press the key,
press
ENTER
again and skip to step 11.
If you want to delay the polling (perhaps to take advantage of lower phone
rates), press
COMMUNICATION OPTIONS
,
ENTER
.
9.
There’s a choice to make. Instruct your fax to carry out this delayed command
in one of the following ways:
Summary of Contents for MFX-1500
