background image

 

9 of 9

 

Document Number: 020009017  May 12, 2022

Subject: BIC Tune Up 

 

‰

Verify operation with manager? Step 1 page 2. Note manager concerns: 

 ___________________________________________ 

 ___________________________________________ 

 ___________________________________________ 

 ___________________________________________ 

 ___________________________________________ 

 ___________________________________________ 

 ___________________________________________

 

‰

Record firmware and recipe versions at beginning of Tune Up? Step 2 page 2.  

UI SW VERSION ____________   SRB SW VERSION __________  

LEFT MIXER SW ____________   RIGHT MIXER SW  __________  

FILE __________________   MENU CONNECT    __________

 

‰

Record “DRINKS SINCE INSTALLATION”? Step 3 page 2.  

LEFT MIXER COUNT _________   TOTAL COUNT  ____________  

RIGHT MIXER COUNT _________

 

‰

Record “DRINKS SINCE LAST MAINTENANCE  DATE” . Step 3 page 2.  

LEFT MIXER COUNT _________   TOTAL COUNT  ____________  

RIGHT MIXER COUNT _________

 

‰

Replace Blender Grate O-rings? Step 7 page 2.

 

‰

Pour beverage drain cleaner down the left blend chamber  drain, dispense area 

drain and the right blend chamber drain? Step 14 page 2.

 

‰

Replaced the LMS Valves? Step 16 - Step 22 page 4.

 

‰

Remove the ice bin. Step 24 & Step 25 page 4.

 

‰

Replaced the shaver blade? Step 28 page 4. 

 

‰

Remove the ice shaver gasket from the ice bin and/or the  top of the dispense area 

cover? Clean the surface areas? Step 31 page 4.

 

‰

Replace the shaver gasket? Step 33 page 4.

 

‰

Wash, rinse and sanitize the ice bin? Step 30 page 4.

 

‰

Pour beverage drain cleaner down the ice condensate bowl drain opening? Step 27 

page 4.

 

‰

Replaced the shaver belt? Step 39 & 40 on page 5.

 

‰

Replace the CO2 and Water supply line O-rings? Step 43 & 44 on page 6.

 

‰

Clean the condenser coil? Step 45 page 6.

 

‰

Clean the condensate pan? Step 46 page 6.

 

‰

Clean the condensate drain line? Step 47 page 6.

 

‰

Pour hot water down drain openings of the ice bin, right blend chamber, dispense 

area, and left blend chamber? Step 49 page 6.

 

‰

Work the drains by hand squeezing out any buildup? Step 51 - 52 on page 6.

 

‰

Connect water, CO2, drain, and power cord?  Step 55 page 6.

 

‰

Rear drain line connected correctly to store drain?         

‰

YES          

‰

NO

 

‰

Set the water pressure regulator to 35 psi dynamic? Step 56 page 6.

 

‰

Set the CO2 pressure regulator to 35 psi dynamic? Step 56 page 6.

 

‰

Re-install all exterior panels?  Step 58 page 7.

 

‰

Retrieve product from the walk in cooler and return to the  BIC refrigerated cabinet? 

Step 60 page 7.

 

‰

Verify and assign flavor slot assignments in accordance to  McDonald’s Corporate? 

Step 60 page 7.

 

‰

Complete the Zone 2 cleaning? Step 59 page 7.

 

‰

Confirm  “CONFIGURE YOGURT SMALL DISPENSE” to zero (0). Step 63 page 7.

 

‰

Confirm “PLUNGE SPEED” is set at 15. Step 65 page 8

 

‰

Confirm “CUP OFFSET” is set at 2.0. Step 65 page 8

 

‰

Perform calibration for all flavors, water, and ice?  Step 66 page 8.

 

‰

Reset “LAST MAINTENANCE DATE”? Step B page 8.

 

‰

Make samples of drinks with manager present. Step 69 page 8.

 

‰

Fax or email completed Tune Up Checklist to the RISE Group at  920-683-

7592 or [email protected]

 

‰

Submit claim for service work through Multiplex Claims Processing System.  

Tune Up Checklist MUST be attached to claim or claim will be DENIED. 

Technician Signature:  

 Date: 

 

Technician Printed Name:  

 

Time In:  

Service Agent:  

 

Time Out:  

By signing this you agree that the Preventive Maintenance has been done completely and is satisfactory.

Store Manager/Operator Signature:  

 Date: 

 

Store Manager/Operator Printed Name:  

 

Time:  

BIC TUNE UP CHECKLIST

Store #   
Store Address  
  

 

  

 

 

Store Phone #  

Serial Number  

 

Model  

Summary of Contents for BIC MA-8-2










Reviews: