MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 53

Page: 53 / 196

Ultima S / SL Flex & Pro

3/2019

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

114060421

Move the hook arm / middle frame together with the container to rearmost

position

- move the

CONTROL LEVER

slowly backwards (2GCC)

- press

MAIN CYLINDERS BACK

button (2GMR and 2GRC)

- the indicator light

FRAME NOT DOWN

comes on as the middle frame is rising

from the subframe.

10.

Release the parking brake when the container rear end

touches the ground.

Only in case the truck is on uphill slope, you may not release

the hand brake, as in that case the truck and the container

would move backwards.

NOTE!

In some cases the container will push the truck forward.

Assist this, if necessary, by steering the truck and simultaneously

holding the control lever in backward position.

Third

Move the

LED

Button

control lever

comes

back on

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands