MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 177

Page: 177 / 196

177

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

>>>

ERROR CODE

COMMENTS / PROBLEM

LOCATION

PROGRAM DESCRIPTION

POSSIBLE ACTION

CONSEQUENCE

d009

MIDDLE FRAME IS UP (NOT NEARLY DOWN)

MIDDLE FRAME IN WRONG POSITION

d010

MIDDLE FRAME IS DOWN

MIDDLE FRAME IN WRONG POSITION

d011

MIDDLE FRAME IS NEARLY DOWN

MIDDLE FRAME IN WRONG POSITION

d012

REAR FRAME IS UP (NOT DOWN)

REAR FRAME IN WRONG POSITION

d013

REAR FRAME IS DOWN

REAR FRAME IN WRONG POSITION

d014

ARM IS NOT IN BACK POSITION

TELESCOPIC / TILTING ARM IN WRONG

POSITION

SLIDE / TILT BWD OR CHECK THE HORIZONTAL

MOVEMENT BACK SENSOR

d015

ARM IS IN BACK POSITION

TELESCOPIC / TILTING ARM IN WRONG

POSITION

d016

PULL LIMITER IS ACTIVE

SLIDE / TILT BWD OR CHECK THE PULL LIMITER

SENSOR

NO SLIDE FWD

d017

CRANE BODY IS ACTIVE

CRANE BODY ON IS ACTIVE

SLIDE / TILT BWD OR CHECK THE CRANE BODY

SENSOR

NO SLIDE FWD

d018

CATCH LOCKING RIGHT ARE ACTIVE

OPEN THE RIGHT SIDE CATCH LOCKING / CHECK

THE SENSOR

NO HOOKLIFT

FUNCTION

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands