MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 132

Page: 132 / 196

132

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

>>>

Function button configuration mode

In this mode, the function buttons F1 – F4 can be configured for a control function. The

menu is accessed by pressing “ok” and one of the function button simultaneously.

To decide which function button is selected for configuration, the corresponding function

button shall be pressed once, after which the selected symbol location is highlighted.

Use the D-pad to select a function from the list and assign the selected function to the

selected button by pressing the “ok” button.

After configuring the functions, the mode is exited by pressing the “ok” button for 2 seconds.

Function buttons

F1, F2

Function buttons

F3, F4

D-pad

Configured functions

List of functions

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands