MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 105

Page: 105 / 196

105

Ultima S / SL Flex & Pro

3/2019

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

114060421

>>>

NOTE! Remember to open the front locks before tipping or unloading

the container. If the front locks are closed for some reason when the

tipping device is in the upper position, codes d018 and/or d019 will

be shown on the control display. In this case, open the front locks

before lowering the tipping device in order to avoid damage to the

front locks.

Function

Body locks are closed,

Body locks and front

front locks are opened

locks are opened

LED is slowly flashing

LED is burning continuously

LEDs

2GCC

Display

and LEDs

2GRC

LEDs

2GMR

Function

Open the front locks

Close the front locks

LED comes on

LED off

LEDs

2GCC

Display

and LEDs

2GRC

LEDs

2GMR

Button

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands