MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 52

Page: 52 / 196

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

OPEN

Button

Second LED

comes on

Open the hydraulic body locks

- press the

BODY LOCK

button

LOCKS NOT CLOSED

signal light lit on the control unit when the locks are

open.

Open the mechanical or hydraulic front locks (optional).

Move the hook arm fully rearward position

- move the

CONTROL LEVER

to left and back (2GCC)

- press the

HOOK ARM BACK

button (2GMR and 2GRC)

- start at idle and increase the engine speed gradually.

Mechanical tipping lock will be opened in the rear position of the hook arm.

Two

Move the

LEDs

Button

control lever

are on

to left and back

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands