MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 35

Page: 35 / 196

Ultima S / SL Flex & Pro

3/2019

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

114060421

16.

Move the hook arm forward

- move the

CONTROL LEVER

to left and forward (2GCC)

- press the

HOOK ARM FORWARD

button (2GMR and 2GRC).

Continue the movement until the container is in its transport position.

Movement will close also the mechanical tipping lock.

17.

Close the hydraulic body locks

- press the

BODY LOCKS CLOSED

button.

Signal light

LOCKS NOT CLOSED

must go out.

Also close the mechanical or hydraulic front locks (optional).

Move the

control

lever to left

forward

Two LEDs

are on

Button

Second

LED

goes out

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands