MULTILIFT Ultima S Flex User And Maintenance Manual Download Page 153

Page: 153 / 196

153

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

Oil qualities

Hydraulic system sets many requirements to the hydraulic oil characteristics.

They contain amongst others:

•   Lubrication requirements
•   Oxidation prevention capability
•   Corrosion protection
•   Defoaming quality
•   High viscosity index, in other words, low change of viscosity when the oil is heated.

In order to meet these requirements and qualities, additives are used in oils. Therefore

it is important that the selected oil meets the characteristics for the operating

environment in question. A lower ambient temperature is the same as the lowest starting

temperature.

NOTE!

Vegetable based bio oils are not allowed to be used.

Only synthetic environment friendly oils that meet

the above mentioned requirements are allowed.

NOTE!

Do not mix different oil qualities. Mixing of different oils

weakens generally their characteristics. If it is necessary to use

an alternative oil, check with the supplier the characteristics and

correspondence with the recommended oil.

Changing to biodegradable oil

To obtain the best results, the percentage of the mineral oil left in the system should not

exceed 2%. The “Changing to biodegradable oil” –procedure might also apply to new

systems because the hooklift is tested with mineral oil at the factory if otherwise noticed.

Summary of Contents for Ultima S Flex





































































































































































































Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands

MULTILIFT Ultima S Flex, User And Maintenance Manual

Search results

Summary of Contents for Ultima S Flex

Reviews:

Brands by name

Popular brands