manualshive.com logo in svg

MTU M015710/04E, Operating Instructions Manual

Share
Download
MTU M015710/04E Operating Instructions Manual Download Page 177

7.18 Battery-Charging Generator

7.18.1 Battery-charging generator drive – Drive belt tension adjustment

Preconditions

☑ Engine is stopped and starting disabled.

WARNING

Spring/circlip/tensioning roller preload.

Risk of injury!

• Only use specified tool and equipment.

Adjusting belt tension

1.

Remove protective cover.

2.

Slacken screws (1) and (2) by half a turn.

Result:

Belt tensioner moves against the drive belt

and tensions it.

3.

Tighten screw (2) with torque wrench to the specified tightening torque.

Name

Size

Type

Lubricant

Value/Standard

Screw

M10x1.5

Tightening torque

60 Nm +5 Nm

4.

Tighten screw (1) to specified tightening torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Screw

M10x1.5

Tightening torque

42 Nm

5.

Install protective cover.

192 | Task Description | M015710/04E 2012-09

TIM-ID: 0000031049 - 002

Summary of Contents for M015710/04E





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands