MTU M015710/04E Operating Instructions Manual Download Page 159

Page: 159 / 196

7.14.3 Centrifugal oil filter – Cleaning and filter sleeve replacement

Preconditions

☑ Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 6-50 Nm

F30027336

Cold cleaner (Hakutex 60)

X00056750

Filter sleeve

(→ Spare Parts Catalog)

Sealing ring

(→ Spare Parts Catalog)

Sealing ring

(→ Spare Parts Catalog)

WARNING

Hot oil.

Oil can contain combustion residues which are harmful to health.

Risk of injury and poisoning!

• Wear protective clothing, gloves, and goggles / safety mask.

• Avoid contact with skin.

• Do not inhale oil vapor.

WARNING

Compressed air

Risk of injury!

• Do not direct compressed-air jet at persons.

• Wear protective goggles / safety mask and ear protectors.

174 | Task Description | M015710/04E 2012-09

TIM-ID: 0000000934 - 009

Summary of Contents for M015710/04E





































































































































































































Search results

Summary of Contents for M015710/04E

Reviews:

Brands by name

Popular brands

MTU M015710/04E, Operating Instructions Manual

Search results

Summary of Contents for M015710/04E

Reviews:

Brands by name

Popular brands