manualshive.com logo in svg

MTU 12 V 4000 L63, Operating Instructions Manual

Share
Download
MTU 12 V 4000 L63 Operating Instructions Manual Download Page 97

153272 – HI Misfire Integrator B2

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

153273 – HI Misfire Integrator B3

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

153274 – HI Misfire Integrator B4

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

153275 – HI Misfire Integrator B5

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

153276 – HI Misfire Integrator B6

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

153277 – HI Misfire Integrator B7

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

153278 – HI Misfire Integrator B8

Yellow alarm. Initiated by SAM.

Cause

Corrective action

Misfiring was detected in this

cylinder.

1. Check emission values.

2. Check spark plug (energy level ignition system).

MS150058/01E 2012-07 | Troubleshooting | 97

TIM-ID: 0000017543 - 001

Summary of Contents for 12 V 4000 L63



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands