manualshive.com logo in svg

MTU 12 V 4000 L63, Operating Instructions Manual

Share
Download
MTU 12 V 4000 L63 Operating Instructions Manual Download Page 142

6.3.5 Spark plug – Removal and installation

Preconditions

☑ Engine is stopped and starting disabled.
☑ Open protective packing of new spark plug only immediately prior to installation.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 10-60 Nm

F30452769

1

Spark plug socket wrench, 20.8 mm

F30452574

1

Assembly compound (Molykote P 37)

50564

1

Spark plug

(→ Spare Parts Catalog)

Sealing ring

(→ Spare Parts Catalog)

Spark plug connector with ignition cable

(→ Spare Parts Catalog)

Locking plate

(→ Spare Parts Catalog)

WARNING

Component is hot.

Risk of burning!

• Wear protective gloves.

WARNING

Compressed air

Risk of injury!

• Do not direct compressed-air jet at persons.

• Wear protective goggles / safety mask and ear protectors.

Removing spark plug

1.

Remove ignition cable (2) from ignition coil.

2.

Remove screws (4) and locking plate (5)

from cylinder head cover (1).

3.

Remove spark plug connector (3) with igni‐

tion cable (2) from spark plug.

4.

Unscrew spark plug a few threads.

5.

Clean spark-plug recess with compressed

air.

6.

Unscrew spark plug from cylinder head.

7.

Remove the lower gasket on ignition line

(see instructions for changing ignition line

gasket).

142 | Task Description | MS150058/01E 2012-07

TIM-ID: 0000029131 - 002

Summary of Contents for 12 V 4000 L63



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands