manualshive.com logo in svg

MTU 12 V 4000 L63, Operating Instructions Manual

Share
Download
MTU 12 V 4000 L63 Operating Instructions Manual Download Page 33

2.6.3 Purpose of the units

Engine governor ADEC (ECU 7)

Central control and monitoring unit for the engine
• Communication with other devices and higher-level systems via CAN bus

• Control of throttles (mixture and gas)

• Acquisition and evaluation of engine operating states

• Limit value monitoring

• Self-monitoring and self-diagnostic functions

• Integral status/fault display

• Fault memory

• Large number of inputs/outputs provided:

• Genset side: 14 inputs, 7 outputs, 2 serial interfaces,

• Engine side: 39 inputs, 28 outputs, 1 serial interface

• Engine and genset-related parameter settings in flash memory

• In case of inadmissible states and limit value violations: Initiation of power reduction, engine stop or

emergency engine stop (configurable)

• Diagnostic function via CAN interface (Default CAN1, connection for dialog unit provided)
Software structure:

• One data record for engine software

• One data record for genset software

MS150058/01E 2012-07 | Product Summary | 33

TIM-ID: 0000017541 - 001

Summary of Contents for 12 V 4000 L63



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands