MQ Power DIS185SSI4F Operation Manual Download Page 69

Page: 69 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 69

TROUBLESHOOTING (COMPRESSOR)

Table 15. Troubleshooting (Compressor)

Sympton

Possible Problem

Corrective Action

Air Pressure too high

Pressure sensor defective?

Check or replace sensor

Proportional solenoid valve frozen?

Check or replace solenoid

Inlet valve seal damaged?

Check or replace inlet valve

Air pressure control pipe frozen?

Check or replace air pressure control pipe

Compressor oil too thick?

Replace with proper oil viscosity

Problem in Fuel System

Fuel tank empty?

Add fuel

Air mixed in fuel system?

Fully extract air. Check for loosened fuel line

Fuel filter clogged?

Check or replace fuel filter and clean tank

Fuel has deteriorated?

Add fuel. Check or replace entire fuel system

Fuel injection system is defective?

Check or replace fuel injection system.

Engine oil level too full?

Reduce oil to correct engine oil level

Engine oil is too thick?

Refill engine crankcase with correct type of oil for cold weather

conditions

Engine oil pressure is reduced?

Replace engine oil and filter

Engine overheats?

Clean cooling air system and cooling fin areas

Warm up time not sufficient in cold weather

conditions?

Comply with cold starting instructions and proper oil viscosity.

Emergency Stop Circuit is

Abnormal

Switch or sensor is defective?

Check or repair switch or sensor

Wiring to water temp. sensor, oil pressure

sensor, discharge air temp. sensor is

disconnected?

Check or repair water temp. sensor, oil pressure or discharge air

temp. sensor

Engine control unit is defective?

Replace or repair engine control unit

No Air Is Delivered

Service valve is closed?

Open valve

Minimum pressure valve is abnormal?

Clean or replace pressure valve

Proportional solenoid valve is abnormal?

Check or replace solenoid valve

Pressure sensor P1 or P2 is abnormal?

Check or replace pressure sensor P1 or P2

Safety Valve Operates

Pressure control piping is frozen?

Check or replace frozen pressure control piping

Proportional solenoid valve is frozen?

Check or replace frozen proportional solenoid valve

Air leaks from control pressure pipe?

Check or replace control pressure pipe

Pressure sensor P1 or P2 is frozen?

Check or replace pressure sensor P1 or P2

Safety valve is set to low value?

Replace safety valve

Air leaks from inlet valve seal?

Check or replace inlet valve seal

Summary of Contents for DIS185SSI4F











































































Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands

MQ Power DIS185SSI4F, Operation Manual

Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands