MQ Power DIS185SSI4F Page 13 Operation Manual Download

Page: 13 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 13

SAFETY INFORMATION

EMISSIONS INFORMATION

NOTICE

The diesel engine used in this equipment has been

designed to reduce harmful levels of carbon monoxide

(CO), hydrocarbons (HC) and nitrogen oxides (NOx)

contained in diesel exhaust emissions.
This engine has been certifi ed to meet US EPA Evaporative

emissions requirements in the installed confi guration.
Attempting to modify or make adjustments to the engine

emission system by unauthorized personnel without proper

training could damage the equipment or create an unsafe

condition.
Additionally, modifying the fuel system may adversely affect

evaporative emissions, resulting in fi nes or other penalties.

Emission Control Label

The emission control label is an integral part of the emission

system and is strictly controlled by regulations.
The label must remain with the engine for its entire life.
If a replacement emission label is needed, please contact

your authorized engine distributor.

Summary of Contents for DIS185SSI4F











































































Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands

MQ Power DIS185SSI4F, Operation Manual

Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands