MQ Power DIS185SSI4F Page 43 Operation Manual Download

Page: 43 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 43

CONNECTING BOOSTER/JUMPER CABLES

Before attempting to jump start, attach booster cables to

the air compressor and make sure of the following:

Make sure booster cables are of adequate size to match

current capacity of battery.

Source battery (working battery) should be of equal

voltage and amperage as battery being jumped.

When attaching booster cable clamps, make sure clamps

are attached firmly to battery posts. This will prevent

arcing.

Never allow the positive and negative booster cables to

make contact when connected to a live battery.

When connecting the booster cable with the

BLACK

clamp to the air compressor's ground point, the ground

point should be at least 1 ft. (305 mm) away from the

battery.

The following steps outline the procedure for

connecting

booster cables to the air compressor's battery.
1. Connect one end of the booster cable with the

RED

clamp (Figure 59) to the positive terminal on the air

compressor's battery.

Figure 59. Connecting Booster Cables

2. Connect the other end of the booster cable with the

RED

clamp to the positive terminal on the source

battery (working good battery).

3. Connect one end of the booster cable with the

BLACK

clamp to the negative terminal on the source battery.

SOURCE

BATTERY

(GOOD BATTERY)

AIR

COMPRESSOR

BATTERY

(LOW VOLTAGE)

POS.

NEG.

POS.

RED

CHASSIS GND,

ENGINE BLOCK

1 FT.

(305 MM)

MINIMUM)

BLACK

NEG.

BOOSTER

CLAMP (4)

BOOSTER

CABLE

BOOSTER

CABLE

MAINTENANCE (ENGINE)

4. Connect the other end of the booster cable with the

BLACK

clamp to the negative ground point (chassis

ground/frame) on the air compressor.

REMOVAL OF BOOSTER/JUMPER CABLES

The following steps outline the procedure for

removing

booster cables from the air compressor's battery.
1. Remove the booster cable with the

BLACK

clamp

(Figure 60) from the negative ground point (chassis

ground/frame) on the air compressor.

Figure 60. Removing Booster Cables

2. Remove the other end of the booster cable with the

BLACK

clamp from the negative terminal on the source

battery.

3. Remove the booster cable with the

RED

clamp from

the positive terminal on the source battery.

4. Remove the other end of the booster cable with

the

RED

clamp from the positive terminal on the air

compressor.

SOURCE

BATTERY

(GOOD BATTERY)

AIR

COMPRESSOR

BATTERY

(LOW VOLTAGE)

POS.

NEG.

POS.

RED

CHASSIS GND,

ENGINE BLOCK

1 FT.

(305 MM)

MINIMUM)

BLACK

NEG.

BOOSTER

CLAMP (4)

BOOSTER

CABLE

BOOSTER

CABLE

Summary of Contents for DIS185SSI4F











































































Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands

MQ Power DIS185SSI4F, Operation Manual

Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands