MQ Power DIS185SSI4F Page 21 Operation Manual Download

Page: 21 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 21

MAJOR COMPONENTS (FRONT/REAR/TOP)

Figure 7. Major Components (Front, Rear And Top)

RUN

PREHEAT

HOUR METER

MAIN SWITCH

OFF

PSI AIR PRESSURE

rpm ENGINE SPEED

FUEL LEVEL

MENU

1/2

°F AIR TEMPERATURE

°F WATER TEMPERATURE

DISPLAY

ERROR CODE

CAUTION: Before using, be sure to read Instruction Manual

WARM UP TIME

Auto (Min. 20) - 180 Sec

STOP

QUARTZ

REAR

FRONT

TOP

35.

Exhaust Port

— Never block this exhaust port. Use

only in well-ventilated areas. Always vent exhaust gas

outside.

36.

Coolant Inlet Port

— Remove cover plate to add

coolant to the radiator. Never remove radiator cap

when radiator is hot.

37.

Lifting Hook

— Attach a suitable lifting device,

capable of lifting 2400 lbs. (1,089 kg), to this lifting

point. This lifting point has been positioned for a fully

balanced/configured air compressor. Removal of any

components will unbalance the compressor.

38.

Control Panel

— Includes digital controller and status

LEDs. Digital controller is linked to the electronic control

unit of the engine.

39.

Hour Meter

— Indicates the number of hours machine

has been in use.

40.

Ignition Switch

— To start engine, insert key into

ignition switch (main switch) and turn clockwise to the

position. When unit is not in use, turn ignition key

OFF

position and remove key.

41.

Left Tail/Brake Light

— Before towing the air

compressor, make sure that light is operational and

is working correctly.

NEVER

tow the air compressor if

light is inoperative.

42.

License Plate Light

— This light illuminates the

license plate.

NEVER

tow the air compressor if light

is inoperative.

43.

Air Output Valves

— Connect pneumatic air tools to

these valves.

NEVER

remove air hoses from these

valves while residual air pressure exists. Make sure

there is no residual air pressure before removing hoses.

44.

Right Tail/Brake Light

— Before towing the air

compressor,make sure that light is operational and is

working correctly.

NEVER

tow the air compressor if

light is inoperative.

45.

Storage Compartment

— Use this compartment to

store tools, hoses etc.

Summary of Contents for DIS185SSI4F











































































Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands

MQ Power DIS185SSI4F, Operation Manual

Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands