MQ Power DIS185SSI4F Page 65 Operation Manual Download

Page: 65 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 65

SYSTEM ERROR FAULT CODES

Table 13. Engine/Air Compressor Error Codes

Engine Status Error Code

Details of Trouble

Corrective Action

Engine

Shutdown

E 01

P1 Pressure Sensor abnormal.

Check harness connector at pressure sensor P1.

E 02

P2 Pressure Sensor abnormal.

Check harness connector at pressure sensor P2.

E 03

P3 Pressure Sensor abnormal.

Check harness connector at pressure sensor P3.

E 04

Discharge Air Temp. Sensor abnormal.

Check harness connector at discharge air temp sensor.

E 05

Fuel Level Sender abnormal.

Replace fuel sender.

E 06

Controller circuit board signal error "1".

Check harness connectors between circuit board (CU-40)

and display board (CM-40).

E 07

Controller circuit board signal error "2".

Check the harness connectors between circuit board

(CU-40) and display board (CM-40).

E 10

Engine Low Speed

Adjust using load.

E 11

Battery Charging abnormal.

Check fan belt. Adjust using load. Inspect charge relay

circuit for charging generator.

E 12

Emergency Stop device "1" signal input.

(Option)

L.oil.P

Engine Low oil pressure

Replenish engine oil.

H.co.t

High Engine Coolant Temperature.

Check coolant system for leaks and radiator for coolant

level.

E 14

Low Fuel Level. (Empty)

Refill fuel.

E 15

Engine controller processing time out error

Check DTC codes. Restart the engine.

E 16

Emergency Stop device "2" signal input.

(Option)

E 18

Engine CAN signal error.

Check the CAN wires between circuit board (CU-40) and

ECM.

E 20

High Discharge Air Temperature.

Check and clean oil cooler. Replenish compressor oil.

E 22

Discharge Air pressure abnormally high

Check and repair proportional solenoid valve.

E 23

Proportional Sol. V abnormally low current

Inspect the harness between proportional solenoid valve,

circuit board (CU-40), and ECM.

E 24

Proportional Sol. V over current.

E 97

Memory error.

Turn main switch OFF and ON again. If error code

remains, replace circuit board (CU-40).

E 99

Controller microprocessor WDT error.

Turn main switch OFF and ON again. If error code

remains, replace circuit board (CU-40).

(No engine

behavior

change)

A 10

Engine Air Filter clogging.

Check and clean air cleaner element.

A 21

Compressor Oil Filter clogging.

Replace compressor oil filter.

EMERGENCY STOP AND DIGITAL CONTROLLER DISPLAY

The engine will not start if an error is detected before starting. If an error is detected during operation, the engine will

be shutdown and the digital controller will display the error code and the error code LED will light. Error codes that are

displayed with an "E" are emergency shutdown codes. Error codes that are displayed with an "A" are alarm codes. Reference

Table 14 (next page) for engine sensor error DTC codes. Reference Table 13 below for a brief explanation of the engine

and air compressor error codes.

Summary of Contents for DIS185SSI4F











































































Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands

MQ Power DIS185SSI4F, Operation Manual

Search results

Summary of Contents for DIS185SSI4F

Reviews:

Related manuals for DIS185SSI4F

Brands by name

Popular brands