Moxa Technologies AirWorks AWK-3131A User Manual Download Page 67 | Manualshive

Page: 67 / 109

background image

AirWorks AWK-3131A

Web Console Configuration

3-52

Syslog

This function provides the event logs for the Syslog server. The function supports up to three configurable
Syslog servers and Syslog server UDP port numbers. When an event occurs, the event will be sent as a
Syslog UDP packet to the specified Syslog servers.

Syslog Event Types

Detailed information for the grouped events is shown in the following table. Check the box for Enable
logging to enable the grouped events. All default values are enabled (checked). Detailed descriptions of the
event types are available in the

System Logs

section.

Syslog Server Settings

You can configure the parameters for your Syslog servers in this page.

Syslog server 1/ 2/ 3

Setting

Description

Factory Default

IP address

Enter the IP address of the 1st/ 2nd/ 3rd Syslog Server

None

Syslog port

Setting

Description

Factory Default

Port destination
(1 to 65535)

Enter the UDP port of the corresponding Syslog server

514

NOTE

The RSSI report events (Only for Client mode) event type is useful during the site survey stage and
uses a special utility to draw RSSI table values. However, this function increases the traffic load; we
recommend setting this function to disable during normal usage.

«
...
65
66
67
68
69
...
»

Summary of Contents for AirWorks AWK-3131A














































































































Reviews:

No comments

Related manuals for AirWorks AWK-3131A

Brand: Keithley Pages: 73

Brand: Rainforest Automation Pages: 29

5-in-1 PC Card Adapter TS0MADP5

Brand: Transcend Pages: 2

KAT Walk C PiSystem Adapter

Brand: KAT VR Pages: 12

Brand: TP-Link Pages: 33

Brand: National Instruments Pages: 19

Brand: Kraun Pages: 25

dx-uc202 - USB 2.0 PCMCIA Notebook Card

Brand: Dynex Pages: 16

Brand: ZyXEL Communications Pages: 2

ZyXEL ZyAIR B-220

Brand: ZyXEL Communications Pages: 51

Brand: ZyXEL Communications Pages: 2

PowerLine PL-100

Brand: ZyXEL Communications Pages: 33

Brand: ZyXEL Communications Pages: 64

Brand: ZyXEL Communications Pages: 97

802.11g Wireless Ethernet Adapter 1-G-470

Brand: ZyXEL Communications Pages: 14

DMA-1000 Series

Brand: ZyXEL Communications Pages: 192

Brand: Trust Pages: 2

Brand: Resol Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands