manualshive.com logo in svg

Moxa Technologies AirWorks AWK-3131A, User Manual, Page: 74 / 109

Share
Download
Moxa Technologies AirWorks AWK-3131A User Manual Download Page 74

AirWorks AWK-3131A 

Web Console Configuration 

 

3-59 

DI and Power Status 

The status of power inputs and digital inputs is shown on this web page. The status will refresh every 5 
seconds if the Auto refresh box is checked.   

 

AeroLink Protection Status (For Client/Slave Mode Only) 

After you have enabled AeroLink Protection in the Advanced WLAN Setup panel, the current state of the 
AeroLink Protection is displayed here for easy diagnosis. 

 

A member of the AeroLink Protection group can take one of the following seven states: 

•

 

Initiation State (Init): Initiates the AeroLink Protection Protocol 

•

 

Discovering State (Discover): Discovers other AeroLink Protection members for further negotiation 

•

 

Idle State (Idle): Internal protocol checkpoint 

•

 

Negotiation State (Nego): Negotiates with other AeroLink Protection members and elects an Active 
node. 

•

 

Backup State (Backup): After negotiation, this node is assigned as a Backup node. All traffic will go 
through the Active node instead. 

NOTE 

When a node is in Backup state, the STATE LED will be blinking. 

 

•

 

Active State (Active): After negotiation, this node is assigned as Active node, which means that all 
traffic will go through this node. 

•

 

Role Change State (Change): If the Active node is no longer capable of data transmission via the 
WLAN, it will turn into Change State to trigger the re-negotiation of the Active node from the Backup 
nodes. 

 
AeroLink Protection function can adopt one of the following detection methods:   

•

 

SNR: Checks the Signal-Noise Ratio (SNR) of the associated client 

•

 

Signal Strength: Checks the Signal Strength of the associated client 

•

 

Disconnection: Checks for disconnection 
 

 
 
 
 
 
 
 

Summary of Contents for AirWorks AWK-3131A














































































































Reviews:

No comments