Moxa Technologies AirWorks AWK-3131A User Manual Download Page 24

Page: 24 / 109

AirWorks AWK-3131A

Web Console Configuration

3-9

Device name

Setting

Description

Factory Default

Max. 31 of characters This option is useful for specifying the role or application of

different AWK-3131A units.

Model name

<Last

3 bytes of the
device MAC>

Device location

Setting

Description

Factory Default

Max. of 31 characters Specifies the location of different AWK-3131A units.

None

Device description

Setting

Description

Factory Default

Max. of 31 characters Use this space to record a more detailed description of the

AWK-3131A

None

Device contact information

Setting

Description

Factory Default

Max. of 31 characters Provides information about whom to contact in order to

resolve problems. Use this space to record contact
information of the person responsible for maintaining this
AWK-3131A.

None

Login Message

Setting

Description

Factory Default

Max. of 31 characters Enter a message to display to all users when they log in

Blank

Login authentication failure message

Setting

Description

Factory Default

Max. of 31 characters Enter the login authentication failure message to display to

the user who logs in with an invalid username or password

None

Interface On/Off

Summary of Contents for AirWorks AWK-3131A













































































































Search results

Summary of Contents for AirWorks AWK-3131A

Reviews:

Related manuals for AirWorks AWK-3131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-3131A, User Manual

Search results

Summary of Contents for AirWorks AWK-3131A

Reviews:

Related manuals for AirWorks AWK-3131A

Brands by name

Popular brands