Moxa Technologies AirWorks AWK-3131A User Manual Download Page 72 | Manualshive

Page: 72 / 109

background image

AirWorks AWK-3131A

Web Console Configuration

3-57

Associated Client List (For AP/Master Mode Only)

The Associated Client List shows all the clients that are currently associated with a particular AWK-3131A.
This page provides useful information for easier network diagnosis:

MAC Address: Displays the associated client MAC address. If DHCP server is enabled on this AP/Master, the
IP address will also be displayed.

Connection Duration: States how long the client has been connecting to this AP/Master.

SNR/Signal Strength: States the Signal-Noise Ratio/Signal Strength of the associated client. This is
especially useful for identifying a weak signal client that is potentially reducing the overall wireless
performance.

Tx (Bytes/Pkts): Records the AP-to-client traffic after a client is associated.

Rx (Bytes/Pkts): Records the client-to-AP traffic after a client is associated.

DHCP Client List (For AP Mode Only)

The DHCP Client List shows all the clients that require and have successfully received IP assignments. You
can click the Refresh button to refresh the list.

You can press Select all button to select all content in the list for further editing.

«
...
70
71
72
73
74
...
»

Summary of Contents for AirWorks AWK-3131A














































































































Reviews:

No comments

Related manuals for AirWorks AWK-3131A

Brand: Icidu Pages: 34

Brand: Rainforest Automation Pages: 29

Brand: Sennheiser Pages: 1

Brand: VOLTCRAFT Pages: 4

Brand: IOGear Pages: 60

Brand: Roche Pages: 2

LANEscape WH2330

Brand: Z-Com Pages: 12

isysNet ControlNet A Series

Brand: Parker Pages: 8

Brand: Intermec Pages: 4

SeaLINK plus 485I

Brand: SeaLevel Pages: 20

Brand: Dynex Pages: 1

Brand: Linksys Pages: 24

Brand: Linksys Pages: 33

Brand: ZJFKSDYX Pages: 14

Brand: OPTOGAMA Pages: 25

Brand: Konig Pages: 68

Brand: Konig Pages: 73

Brand: Tumi Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands