manualshive.com logo in svg

Moxa Technologies AirWorks AWK-3131A, User Manual, Page: 55 / 109

Share
Download
Moxa Technologies AirWorks AWK-3131A User Manual Download Page 55

AirWorks AWK-3131A 

Web Console Configuration 

 

3-40 

 

ATTENTION 

Be careful when you enable the filter function: 
Drop + “

no

 entity on list is activated” = all packets are allowed 

Accept + “

no

 entity on list is activated” = all packets are denied 

 

IP Protocol Filters 

The AWK-3131A’s IP protocol filter is a policy-based filter that can allow or filter out IP-based packets with 
specified IP protocol and source/destination IP addresses.  

The AWK-3131A provides 32 entities for setting IP protocol and source/destination IP addresses in your 
filtering policy. Four IP protocols are available: All, ICMP, TCP, and UDP. You must specify either the 
Source IP or the Destination IP. By combining IP addresses and netmasks, you can specify a single IP 
address or a range of IP addresses to accept or drop. For example, “IP address 192.168.1.1 and netmask 
255.255.255.255” refers to the sole IP address 192.168.1.1. “IP address 192.168.1.1 and netmask 
255.255.255.0” refers to the range of IP addresses from 192.168.1.1 to 192.168.255. Remember to check 
the Active check box for each entity to activate the setting. 

 

IP protocol filters 

Setting 

Description 

Factory Default 

Enable 

Enables IP protocol filters 

Disable 

Disable 

Disables IP protocol filters 

Policy 

Setting 

Description 

Factory Default 

Accept 

Only the packets fitting the entities on the list can be allowed  Drop 

Drop 

Any packet fitting the entities on the list will be denied 

 

 

ATTENTION 

Be careful when you enable the filter function:  
Drop + “

no

 entity on list is activated” = all packets are allowed 

 “

no

 entity on list is activated” = all packets are denied 

 

 

Summary of Contents for AirWorks AWK-3131A














































































































Reviews:

No comments