![background image](http://html1.mh-extra.com/html/moulinex/me-6251/me-6251_user-manual_1840168005.webp)
- Any servicing other than cleaning and normal upkeep by the customer must be carried out by an approved service
centre.
- Do not use the appliance if the power lead is damaged. To avoid all possible danger, have it replaced at an approved
service centre (see list in the service booklet).
- Never place the appliance, the power cord or the plug in water or any other liquid.
- Keep the power lead out of the reach of children.
- The power lead should never touch hot surfaces, or be placed near heat sources or sharp edges.
- For your own safety, only use Moulinex accessories and spare parts which are suitable for your appliance.
- Do not use the appliance for longer than 14 minutes.
- For your safety, this appliance complies with all applicable standards and regulations:
• Low voltage directive
• Electro-magnetic compatibility
• Environmental regulations
• Regulations regarding materials in contact with foodstuffs.
Wash all accessories in soapy water. Rinse and dry carefully.
The screen and blades must be kept lubricated. Apply a little oil to them.
Do not run the appliance empty if the screen has not been oiled.
WARNING! Handle the drums carefully as the blades are extremely sharp.
MINCER HEAD ASSEMBLY (A) :
Assembling the mincer head (figures 1.1 and 1.2)
Hold section
A1
by the hopper with the wider opening at the top. Insert the screw feeder
(A2)
(long shaft first) in the
head assembly
A1
.
Fit the stainless steel blades
(A3)
on the short shaft of the screw feeder
(A2)
, so that the cutting edges face outward.
Fit the screen of your choice over the blades
(A3)
ensuring that the pin fits into the notch on the assembly
(A1)
.
Tighten the locking nut
A5
(do not apply excessive pressure).
Fitting the mincer head to the appliance (diagram 2):
• The motor unit
(H)
must be unplugged. Position the mincer head in front of the unit with the hopper tilted to the
right. Fit the two pins on the mincer head into the two notches on the motor unit.
Push the mincer head firmly into the motor unit
(H)
and then turn the hopper to the left until it locks into position
(the hopper should be vertical).
• Fit the removable tray
(B)
onto the pins of the hopper.
Plug the appliance in. It is now ready for use.
Use:
Prepare all the food you wish to mince, eliminating any bones, cartilage or nerves.
Cut the meat into pieces (approximately 2 cm x 2 cm).
Place a container under the mincer head.
Press the On / Off switch
(F)
to start the appliance.
Place the pieces of meat on the tray
(B)
and use the pusher
(C)
to push them into the hopper one by one.
Never use your fingers or any other object to push the meat into the hopper.
To make extra fine Kebbe or Kefta mince, pass the meat through the mincer 2 or 3 times until it has the right consistency.
Tip:
When you have finished mincing put a few pieces of bread through the mincer to push out all the meat.
What to do if the mincer is blocked (diagram 3)
Turn off the mincer by pressing the On / Off switch
(F)
.
Press the Reverse button
(G)
for a few seconds to clear the blockage.
Press the On / Off switch
(F)
to continue mincing.
Important :
wait until the appliance stops completely before you use the On
(F)
or Reverse
(G)
buttons.
KEBBE ACCESSORY (I)
BEFORE USING THE APPLIANCE FOR THE FIRST TIME:
USING THE APPLIANCE:
2
Summary of Contents for ME 6251
