Motorola SYMBOL DS6707 Product Reference Manual Download

Page: 46 / 424

3 - 2

Symbol DS6707 Digital Imager Scanner Product Reference Guide

Troubleshooting

Table 3-1

Troubleshooting

Problem

Possible Causes

Possible Solutions

The aiming pattern does not appear
when pressing the trigger.

No power to the digital imager
scanner.

If the configuration requires a power
supply, re-connect the power supply.

Incorrect host interface cable is used.

Connect the correct host interface cable.

Interface/power cables are loose.

Re-connect cables.

Digital imager scanner is disabled.

See the technical person in charge of
scanning.

If using RS-232 Nixdorf B mode, CTS
is not asserted.

Assert CTS line.

Aiming pattern is disabled.

Enable the aiming pattern. See

Decode Aiming Pattern on page 4-18.

Scanner emits short low/short
medium/short high beep sequence
(power-up beep sequence) more than
once.

The USB bus may put the digital
imager scanner in a state where
power to the digital imager scanner is
cycled on and off more than once.

Normal during host reset.

Digital imager scanner emits aiming
pattern, but does not decode the bar
code.

Digital imager scanner is not
programmed for the correct bar code
type.

Program the digital imager scanner to
read that type of bar code. See

Chapter

10, Symbologies

Bar code symbol is unreadable.

Scan test symbols of the same bar code
type to determine if the bar code is
defaced.

The symbol is not completely inside
aiming pattern.

Move the symbol completely within the
aiming pattern.

Digital imager scanner emits 4 short
high beeps during decode attempt.

Digital imager scanner has not
completed USB initialization.

Wait several seconds and scan again.

Summary of Contents for SYMBOL DS6707









































































































































































































































































































































































































































Search results

Summary of Contents for SYMBOL DS6707

Reviews:

Related manuals for SYMBOL DS6707

Brands by name

Popular brands

Motorola SYMBOL DS6707, Product Reference Manual

Search results

Summary of Contents for SYMBOL DS6707

Reviews:

Related manuals for SYMBOL DS6707

Brands by name

Popular brands