manualshive.com logo in svg

Motorola PTP 25600, User Manual

The Motorola PTP 25600 is a high-performance wireless communication device designed for reliable and efficient data transfer. To fully understand its features and functionalities, make sure to download the user manual from our website, completely free of cost. Get all the information you need from manualshive.com.

Share
Download
background image

 

Caring for the environment 

 

 
 

phn-0896_009v003 

 

 

Feb 2010 

UNDER DEVELOPMENT 

11

 

 

Caring for the environment 

The following information describes national or regional requirements for the disposal 
of Motorola supplied equipment and for the approved disposal of surplus packaging. 

In EU countries 

The following information is provided to enable regulatory compliance with the 
European Union (EU) directives identified and any amendments made to these 
directives when using Motorola equipment in EU countries. 

 

Disposal of Motorola equipment 

European Union (EU) Directive 2002/96/EC Waste Electrical and Electronic Equipment 
(WEEE) 

Do not dispose of Motorola equipment in landfill sites. In the EU, Motorola in 
conjunction with a recycling partner ensures that equipment is collected and recycled 
according to the requirements of EU environmental law. 

Disposal of surplus packaging 

Do not dispose of surplus packaging in landfill sites. In the EU, it is the individual 
recipient’s responsibility to ensure that packaging materials are collected and recycled 
according to the requirements of EU environmental law. 

In non-EU countries 

In non-EU countries, dispose of Motorola Networks equipment and all surplus 
packaging in accordance with national and regional regulations. 

 

 

Summary of Contents for PTP 25600














































































































































































































































Reviews:

No comments

Related manuals for PTP 25600

ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Brand: ICP DAS USA Pages: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Brand: ICP DAS USA Pages: 15
ICP DAS USA PCIe-S112 Quick Start Manual preview
PCIe-S112
Brand: ICP DAS USA Pages: 8
ICP ZT-2550 Quick Start Manual preview
ZT-2550
Brand: ICP Pages: 14
Datasheen D902AC User Manual preview
D902AC
Brand: Datasheen Pages: 25
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Brand: Enginko Pages: 19
Mylex eXtremeRAID 1100 Installation Manual preview
eXtremeRAID 1100
Brand: Mylex Pages: 74
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Radicom WiFiHU2S-a/c Preliminary Designer’S Manual preview
WiFiHU2S-a/c
Brand: Radicom Pages: 27
NETGEAR RP614 v2 Installation Manual preview
RP614 v2
Brand: NETGEAR Pages: 2
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
TP-Link TL-SG2424P User Manual preview
TL-SG2424P
Brand: TP-Link Pages: 176
Conel UR5i v2 SL User Manual preview
UR5i v2 SL
Brand: Conel Pages: 32
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Brand: Ubiquiti Pages: 23
Hunter Pro-C Series Programming Instructions preview
Pro-C Series
Brand: Hunter Pages: 2
Ubiquiti EdgeRouter 12 Quick Start Manual preview
EdgeRouter 12
Brand: Ubiquiti Pages: 23

Brands by name

Popular brands

Load more brands