manualshive.com logo in svg

Motorola PTP 25600, User Manual

The Motorola PTP 25600 is a high-performance wireless communication device designed for reliable and efficient data transfer. To fully understand its features and functionalities, make sure to download the user manual from our website, completely free of cost. Get all the information you need from manualshive.com.

Share
Download
background image

Wireless operation 

Chapter 1 Product description 

 

 

 

 

phn-0896_009v003 

1-20

 

UNDER DEVELOPMENT 

Feb 2010 

 

Figure 1-12

  The TDD cycle of events 

Master Tx Burst

Master Rx

Slave Rx

Slave Tx Burst

Master Tx Burst

Propagation Delay

Propagation Delay

Processing Delay

Processing Delay

Frame Duration

Master Burst Duration

Slave Burst Duration

Frame 1

Frame 2

Time

 

The Master PTP 600 automatically controls the structure of the TDD Frame, optimizing 
Burst Duration and Frame Duration for either maximum capacity or minimum latency 
depending on the setting of Link Mode Optimization and Link Symmetry.  

When TDD synchronization is enabled (see 

TDD synchronization configuration

 on page 

6-66

), the user must configure the TDD Frame which includes configuration of Burst 

Duration and Frame Duration. 

Link mode optimization 

Link mode optimization allows the PTP 600 link to be optimized according to the type 
of traffic that will be bridged. The link supports two modes, IP Traffic and TDM Traffic. 

IP traffic 

IP Traffic mode is optimized to provide the maximum possible link capacity. IP Traffic 
mode is an appropriate choice where applications in the bridged networks provide 
some measure of reliable transmission, and where very low latency is not critical. IP 
mode supports both fixed and adaptive link symmetry (see 

Link symmetry 

on page 

1-

21

). 

Summary of Contents for PTP 25600














































































































































































































































Reviews:

No comments

Related manuals for PTP 25600

Rabbit 2000 Designers Handbook preview
2000
Brand: Rabbit Pages: 45
Rabbit 2000 Instruction & Reference Manual preview
2000
Brand: Rabbit Pages: 174
Rabbit 2000 Getting Started preview
2000
Brand: Rabbit Pages: 43
D-Link NetDefend DFL-260E Reference Manual preview
NetDefend DFL-260E
Brand: D-Link Pages: 328
D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Brand: D-Link Pages: 2
D-Link DFL-210 - NetDefend - Security Appliance Firewall Registration Manual preview
DFL-210 - NetDefend - Security Appliance
Brand: D-Link Pages: 19
D-Link DFL-M510 Faq preview
DFL-M510
Brand: D-Link Pages: 22
D-Link DFE-680TX Quick Install Manual preview
DFE-680TX
Brand: D-Link Pages: 4
Dahua N300 Quick Start Manual preview
N300
Brand: Dahua Pages: 12
D-Link NetDefend DFL-1600 Quick Manual preview
NetDefend DFL-1600
Brand: D-Link Pages: 23
H3C H3C S7500E-X Command Reference Manual preview
H3C S7500E-X
Brand: H3C Pages: 16
H3C SR6600 SPE-FWM Configuration Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 24
D-Link DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network... User Manual preview
DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...
Brand: D-Link Pages: 53
iDirect iQ Desktop+ Installation, Support, And Maintenance Manual preview
iQ Desktop+
Brand: iDirect Pages: 52
T.A HALL 6370 Instruction Manual preview
HALL 6370
Brand: T.A Pages: 11
Toto Link IP04229 User Manual preview
IP04229
Brand: Toto Link Pages: 55
Ericsson Marconi OMS 1200 Product Description preview
Marconi OMS 1200
Brand: Ericsson Pages: 136
Radicom WiFiHU2S-a/c Preliminary Designer’S Manual preview
WiFiHU2S-a/c
Brand: Radicom Pages: 27

Brands by name

Popular brands

Load more brands