manualshive.com logo in svg

Motorola PTP 25600, User Manual

The Motorola PTP 25600 is a high-performance wireless communication device designed for reliable and efficient data transfer. To fully understand its features and functionalities, make sure to download the user manual from our website, completely free of cost. Get all the information you need from manualshive.com.

Share
Download
background image

User Guide: PTP 600 Series 

Typical deployment 

 

 
 

phn-0896_009v003 

 

 

Feb 2010 

UNDER DEVELOPMENT 

1-3

 

 

Typical deployment 

The PTP 600 Series Bridge consists of an identical pair of units deployed one at each 
end of the link. The radio link operates on a single frequency channel in each direction 
using Time Division Duplex (TDD). One unit is deployed as a master and the other as a 
slave. The master unit takes responsibility for controlling the link in both directions.  

The PTP 600 Series Bridge is aimed at a wide range of applications. An example 
application is an enterprise that has a requirement to connect together the Local Area 
Network (LAN) of two or more buildings as shown in 

Figure 1-1

.  

Figure 1-1  

Typical PTP 600 Series bridge deployment 

 

 

Each end of the link consists of:  

•

 

Outdoor Unit (ODU):

 An integrated (or connectorized - see 

Chapter 8 

Connectorized PTP 600 series

) outdoor transceiver unit containing all the radio 

and networking electronics.  

•

 

PIDU Plus: 

An indoor connection box containing a mains power supply, status 

indicators and network connection port.  

A pair of units is normally supplied pre-configured as a link. 

 

Summary of Contents for PTP 25600














































































































































































































































Reviews:

No comments

Related manuals for PTP 25600

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
Accelerated 6330-MX User Manual preview
6330-MX
Brand: Accelerated Pages: 10
Accelerated 6300-CX Customer Setup Instructions preview
6300-CX
Brand: Accelerated Pages: 4
JCG Q5 Quick Installation Manual preview
Q5
Brand: JCG Pages: 3
Ratoc Systems SmartMedia Adapter PC Card REX-SMA01F Product Manual preview
SmartMedia Adapter PC Card REX-SMA01F
Brand: Ratoc Systems Pages: 75
Observint NVR4 Firmware User Manual preview
NVR4
Brand: Observint Pages: 117
Navini Networks RIPWAVE 40-00460-00R User Manual preview
RIPWAVE 40-00460-00R
Brand: Navini Networks Pages: 35
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
IBASE Technology IB952 Series User Manual preview
IB952 Series
Brand: IBASE Technology Pages: 71
Net to Net Technologies UIM-1000T Installation Instructions preview
UIM-1000T
Brand: Net to Net Technologies Pages: 4
ZyXEL Communications P-974H - V3.70 Manual preview
P-974H - V3.70
Brand: ZyXEL Communications Pages: 116
IntesisBox IBOX-BAC Series Installation Sheet preview
IBOX-BAC Series
Brand: IntesisBox Pages: 2
Linksys WRT54GR - Wireless-G Broadband Router Quick Installation Manual preview
WRT54GR - Wireless-G Broadband Router
Brand: Linksys Pages: 81
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Brand: Accom Pages: 15
Kohler Mira Pixel User Manual preview
Mira Pixel
Brand: Kohler Pages: 32
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
BHU NETWORKS BXM2 User Manual preview
BXM2
Brand: BHU NETWORKS Pages: 75
Renesas REJ06B0734-0100 Application Note preview
REJ06B0734-0100
Brand: Renesas Pages: 19

Brands by name

Popular brands

Load more brands