manualshive.com logo in svg

Motorola PTP 25600, User Manual

The Motorola PTP 25600 is a high-performance wireless communication device designed for reliable and efficient data transfer. To fully understand its features and functionalities, make sure to download the user manual from our website, completely free of cost. Get all the information you need from manualshive.com.

Share
Download
background image

User Guide: PTP 600 Series 

PTP 58600 reference information 

 

 
 

phn-0896_009v003 

 

 

Feb 2010 

UNDER DEVELOPMENT 

4-85

 

 

 

PTP 58600 FCC antenna restrictions 

In FCC regions, external antennas from the lists in 

Table 4-55

 and 

Table 4-56

 can be 

used with the Connectorized version of the PTP 58600. These are approved by the FCC 
for use with the product and are constrained by the following limit for Single/Dual 
Polarization Parabolic Dish Antennas: up to 37.7 dBi per polarization or antenna. 

In FCC regions when using external antennas, cable loss between the connectorized 
version of the PTP 600 Series and the antenna ports must not be less than 1.2 dB. 

CAUTION

 

Antennas not included in this table, or those having a gain greater than the 
specified maximum, are strictly prohibited for use with the PTP 58600. The 
required antenna impedance is 50 ohms. 

Table 4-55  

Allowed antennas for deployment in USA/Canada – 5.8 GHz

 

Manufacturer 

Antenna Type 

Gain 
(dBi) 

Flat 
Plate 

Parabolic 
Dish 

Andrew 

Andrew 1-foot Flat Panel, FPA5250D12-N 
(23.6dBi) 

23.6 Y   

Andrew 

Andrew 2-foot Flat Panel, FPA5250D24-N 
(28dBi) 

28 Y  

Gabriel 

Gabriel 1-foot Flat Panel, DFPD1-52 
(23.5dBi) 

23.5 Y   

Gabriel 

Gabriel 2-foot Flat Panel, DFPD2-52 
(28dBi) 

28 Y  

MTI 

MTI 17 inch Diamond Flat Panel, MT-
485009 (23dBi) 

23 Y  

MTI 

MTI 15 inch Dual-Pol Flat Panel,  
MT-485025/NVH (23dBi) 

23 Y  

MTI 

MTI 2 ft Directional Flat Panel, MT-20004 
(28dBi) 

28 Y  

MTI 

MTI 2 ft Flat Panel, MT-486001 (28dBi) 

28 

Y 

 

Summary of Contents for PTP 25600














































































































































































































































Reviews:

No comments

Related manuals for PTP 25600

ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Brand: ebm-papst Pages: 16
Juniper TX MATRIX PLUS Hardware Manual preview
TX MATRIX PLUS
Brand: Juniper Pages: 502
Accton Technology Fast SwitchHub-8mi SNMP Advanced Reference Manual preview
Fast SwitchHub-8mi SNMP
Brand: Accton Technology Pages: 13
Patton electronics 6103 User Manual preview
6103
Brand: Patton electronics Pages: 12
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Brand: ZALMAN Pages: 9
B&B Electronics 232CC1A Product Information preview
232CC1A
Brand: B&B Electronics Pages: 2
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
Nilox 16NX071900001 User Manual preview
16NX071900001
Brand: Nilox Pages: 66
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
XAVI Technologies Corp. X7822r User Manual preview
X7822r
Brand: XAVI Technologies Corp. Pages: 63
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1
Hama 49276 Operating Instruction preview
49276
Brand: Hama Pages: 7
Intel 80960KB Manual preview
80960KB
Brand: Intel Pages: 44

Brands by name

Popular brands

Load more brands