manualshive.com logo in svg

Motorola PTP 25600, User Manual

The Motorola PTP 25600 is a high-performance wireless communication device designed for reliable and efficient data transfer. To fully understand its features and functionalities, make sure to download the user manual from our website, completely free of cost. Get all the information you need from manualshive.com.

Share
Download
background image

FIPS 140-2 

Chapter 1 Product description 

 

 

 

 

phn-0896_009v003 

1-54

 

UNDER DEVELOPMENT 

Feb 2010 

 

 

Configuring HTTPS/TLS 

The HTTPS/TLS interface is configured using the Security Wizard. See 

Configuring 

FIPS 140-2 mode

 on page 

6-108

 for further details of using the Security Wizard. 

Exiting from the FIPS 140-2 mode 

To exit from the FIPS 140-2 mode, do any of the following: 

•

 

Load a PTP 600 license key that has FIPS operation disabled and reboot. 

•

 

Load PTP 600 software that is not FIPS-validated and reboot. 

•

 

Zeroise CSPs and reboot. 

The critical security parameters (CSPs) are always erased (zeroised) on exit from FIPS 
140-2 mode. 

Prerequisites 

CAUTION

 

To operate in FIPS-140-2 mode ensure that you use: 

o

 

A FIPS-approved cryptographic key generator 

o

 

A FIPS-approved X509 RSA public/private key pair generator with the 

DER output format. 

o

 

A FIPS-approved random number generator 

o

 

A HTTPS-enabled web browser supporting FIPS approved cipher 

specifications. 

 

 

 

Summary of Contents for PTP 25600














































































































































































































































Reviews:

No comments

Related manuals for PTP 25600

Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Brand: IBM Pages: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 78
IBM 9040-MR9 Manual preview
9040-MR9
Brand: IBM Pages: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Brand: IBM Pages: 132
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Brand: Lattice Semiconductor Pages: 13
Ubiquiti Bullet Quick Start Manual preview
Bullet
Brand: Ubiquiti Pages: 40
Furuno 001-558-430 Replacement Instructions Manual preview
001-558-430
Brand: Furuno Pages: 24
Toto Link IP04229 User Manual preview
IP04229
Brand: Toto Link Pages: 55
Altera Nios II Hardware Development Manual preview
Nios II
Brand: Altera Pages: 42
QuickLink QL-CXS Installation Manual preview
QL-CXS
Brand: QuickLink Pages: 8
IDT 89HPES16NT2 User Manual preview
89HPES16NT2
Brand: IDT Pages: 292
UfiSpace S9600-28DX Hardware Installation Manual preview
S9600-28DX
Brand: UfiSpace Pages: 34
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
ekwb EK-FC980 GTX Classy Installation And Mounting Manual preview
EK-FC980 GTX Classy
Brand: ekwb Pages: 2
ENERMAX LIQMAX III ELC-LMT120-ARGB User Manual preview
LIQMAX III ELC-LMT120-ARGB
Brand: ENERMAX Pages: 32

Brands by name

Popular brands

Load more brands