manualshive.com logo in svg

Motorola MVME3600 Series, Programmer'S Reference Manual

Share
Download
Motorola MVME3600 Series Programmer'S Reference Manual Download Page 99

Functional Description

http://www.motorola.com/computer/literature

2-27

2

or the MPC bus. The three low order address bits are exclusive-ORed with 
a three-bit value that depends on the length of the operand, as shown 
below.

Table 2-5.  Address Modification for Little-Endian Transfers

Note

The only legal data lengths supported in little-endian mode are 1, 
2, 4, or 8-byte aligned transfers.

Since this method has some difficulties dealing with unaligned PCI-
originated transfers, the Raven MPC master will break up all unaligned 
PCI transfers into multiple aligned PCI transfers into multiple aligned 
transfers on the MPC bus.

Raven Registers

The Raven registers are not sensitive to changes in big-endian and 
little-endian mode. With respect to the MPC bus (but not always the 
address internal to the processor), the MPC registers are always 
represented in big-endian mode. This means that the processor’s internal 
view of the MPC registers will appear different depending on which mode 
the processor is operating in.

With respect to the PCI bus, the RavenMPIC registers and the 
configuration registers are always represented in little-endian mode.

Data Length

 (bytes)

Address Modification

1

XOR with 111

2

XOR with 110

4

XOR with 100

8

no change

Summary of Contents for MVME3600 Series




















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands