Motorola MVME3600 Series Programmer'S Reference Manual Download Page 202

Page: 202 / 275

3-40

Computer Group Literature Center Web Site

Falcon ECC Memory Controller Chipset

bit also be set while the rwcb bit is set. A possible
sequence for performing read-write check-bits is as
follows:

1. Disable scrub writes by clearing the swen bit if it is set.

2. Stop all DRAM Tester operations by clearing the trun bit.

3. Make sure software is not using DRAM at this point, because while

rwcb is set, DRAM will not function as normal memory.

4. Set the derc and rwcb bits in the Data Control register.

5. Perform the desired read and/or write check-bit operations.

6. Clear the derc and rwcb bits in the Data Control register.

7. Perform the desired testing related to the location/locations that

have had their check-bits altered.

8. Enable scrub writes by setting the swen bit if it was set before.

derc

Setting derc to one alters Falcon pair operation as
follows:

1. During reads, data is presented to the PowerPC 60x data bus

uncorrected from the DRAM array.

2. During single-beat writes, data is written without correcting single-

bit errors that may occur on the read portion of the read-modify-
write. Check-bits are generated for the data being written.

3. During single-beat writes, the write portion of the read-modify-

write happens regardless of whether there is a multiple-bit error
during the read portion. No correction of data is attempted. Check-
bits are generated for the data being written.

4. During refresh/scrub cycles, if swen is set, a read-write to DRAM

happens with no attempt to correct data bits. Check-bits are
generated for the data being written.

derc is useful for initializing DRAM after power-up and
for testing DRAM, but it should be cleared during normal
system operation.

Summary of Contents for MVME3600 Series




















































































































































































































































































Search results

Summary of Contents for MVME3600 Series

Reviews:

Related manuals for MVME3600 Series

Brands by name

Popular brands

Motorola MVME3600 Series, Programmer'S Reference Manual

Search results

Summary of Contents for MVME3600 Series

Reviews:

Related manuals for MVME3600 Series

Brands by name

Popular brands