manualshive.com logo in svg

Motorola MVME3600 Series, Programmer'S Reference Manual

Share
Download
Motorola MVME3600 Series Programmer'S Reference Manual Download Page 101

Functional Description

http://www.motorola.com/computer/literature

2-29

2

Each MERST error bit may be programmed to generate a machine check 
and/or a standard interrupt. The error response is programmed through the 
MPC Error Enable Register on a source by source basis. When a machine 
check is enabled, either the MID field in the MPC Error Attribute Register 
or the DFLT bit in the MEREN Register determine the master to which the 
machine check is directed. For errors in which the master who originated 
the transaction can be determined, the MID field is used, provided the MID 
is %00 (processor 0), %01 (processor 1), or %10 (processor 2). For errors 
not associated with a particular MPC master, or associated with masters 
other than processor 0, 1 or 2, the DFLT bit is used. One example of an 
error condition which cannot be associated with a particular MPC master 
would be a PCI system error.

Transaction Ordering

Raven supports transaction ordering with an optional FIFO flushing 
option. The FLBRD (Flush Before Read) bit within the GCSR register 
controls the flushing of PCI write posted data when performing MPC-
originated read transactions.

When the FLBRD bit is set, Raven will handle read transactions 
originating from the MPC bus in the following manner:

❏

Write posted transactions originating from the processor bus are 
flushed by the nature of the FIFO architecture. The Raven will hold 
the processor with wait states until the PCI bound FIFO is empty.

Error Status

Error Address and Attributes

MATO

From MPC bus

SMA

From PCI bus

RTA

From PCI bus

PERR

Invalid

SERR

Invalid

Summary of Contents for MVME3600 Series




















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands