manualshive.com logo in svg

Motorola MTR2000, Installation And Operation Manual

Share
Download
Motorola MTR2000 Installation And Operation Manual Download Page 71

Installation

44

68P81096E37-N

06/28/05

Verifying Proper Operation

Operation of the station can be verified by:

•

observing the state of the 4 LEDs located on the front panel

•

listening to audible alarms, and 

•

exercising radio operation.

Some station components can become extremely hot during station op-
eration.  Turn off all power to the station, and wait until sufficiently cool 
before touching the station.   

Front Panel LEDs

After turning the station power ON (or after a station reset), the 4 LEDs on 
the station front panel:

1.

Are all lit for about 3 seconds to indicate that they are functional.  
The 

Station Status

 LED appears yellow since both the red and green 

LEDs of this bicolor indicator are lit at the same time.

2.

All go off for about 15 seconds.   

3.

All stay off except for the 

Station Status

 LED which goes red for 

about 6 seconds.   

4.

Now indicate operational status of the station.  The 4 LEDs indicate:

-

PA Keyed

 LED; green  – station PA is keyed.

-

FailSoft

 LED; yellow  – (if set up for trunking) station is not be-

ing controlled from the trunking central controller. 

-

Rx Active

 LED; green  – station is unsquelched.

-

Station

 

Status

 LED;  red/green  – operational status of station.

Station

 

Status

LED

This two-color 

Station

 

Status

 LED (i.e., red or green) indicates the follow-

ing:

FS

FS

FS

LED Color

LED State

Indicates that the…

Off

Off

5V power is not present

Red

On

Station is Not Operational  – 
major failure

Red

Flashing

Station is Operational but Not 
Fully Functional  – minor failure

Green

On

Station is Operating Normally

Red/Green

Alternately Flashing

Station is in Boot Mode

Green

Flashing

Station is in Service Mode

Summary of Contents for MTR2000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands