manualshive.com logo in svg

Motorola MTR2000, Installation And Operation Manual

Share
Download
Motorola MTR2000 Installation And Operation Manual Download Page 41

Installation

14

68P81096E37-N

06/28/05

Figure 3.        Unpacking Procedures - Floor-mount Cabinets

1.

Remove cardboard cover from station.

2.

Cut band as shown.

3.

Remove top packing spacer and 
corrugated corner supports.

4.

Remove antistatic bag.  Do not discard bag, 
it will be reinstalled to protect equipment 
during installation.

5.

Depending on cabinet type, either open or 
remove front and rear doors to gain access to 
the four (4) bolts securing the station to the 
wooden skid.  Remove the bolts and nuts as 
shown.

6.

Use hoist to lift the station from the skid.  
Remove skid and return station to floor.

7.

Replace antistatic bag over station to 
provide protection during installation.

Cardboard 

Cover

Corrugated 

Corner 

Supports

Wooden 

Skid

Cut This 

Band

Top Packing 

Spacer

Antistatic Bag

Wooden 

Skid

Station 

Cabinet

Summary of Contents for MTR2000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands