manualshive.com logo in svg

Motorola MTR2000, Installation And Operation Manual

Share
Download
Motorola MTR2000 Installation And Operation Manual Download Page 57

Installation

30

68P81096E37-N

06/28/05

age resulting from use of any other charging systems will void the war-
ranty.  Refer to qualified sales/service representative for charger 
ordering information.

The station is to be connected to a battery supply that is in accordance 
with the applicable electrical codes for the end use country; for example, 
the National Electric Code ANSI/NFPA No.70 for the U.S.

Cables are supplied with the charging option.  Do not make connections 
directly from the station to the storage battery

.  Connect as shown in 

Figure 10.  

CAUTION

!

Figure 10.        Making Connections to Storage Battery

DC input Connector located  at 
rear of the station for hooking up 
the  Battery backup system.

Required input power:

• Voltage - 14.2 Vdc Low Power (LP)

28.4 Vdc High Power (HP)

• Current - 11.5 Amps LP

13.0 Amps HP

Both positive and negative terminals must be 
protected with appropriate fast acting fuses.
Secondary circuitry must be SELV type and 
be installed nearby, preferable in the same 
building.
All installations shall be carried out by trained 
service personnel only.

Connector ESD 
cover must be in 
place when Battery 
Backup cable is not 
in use  – to prevent 
exposure to live 
contacts.

CAUTION

!

Summary of Contents for MTR2000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands