manualshive.com logo in svg

Motorola MTR2000, Installation And Operation Manual

Share
Download
Motorola MTR2000 Installation And Operation Manual Download Page 44

Installation

68P81096E37-N

17

06/28/05

Installing Slide Rail Assembly in a Motorola Cabinet

Referring to Figure 4, perform the following procedure to install slide rail 
option X968AA.

On a bench-top, working

on one side of the slide rail

assembly at a time…

1.

Remove the Inner-Slide Rail from the slide assembly (left and right) 
by depressing the Slide Locking Latch and sliding the Inner-Slide Rail 
out from the slide assembly. 

2.

Install the Inner-Slide Rail (left) on the Power Supply side by:

-

removing the 2 bottom screws from the station power supply 
EMI cover, and 

-

installing the Inner-Slide Rail (left) with the supplied screws. 

3.

Install the Inner-Slide Rail (right) on the PA side using the holes in the 
PA casing.

4.

Attach each Outer-Slide Rail to a Cabinet Bracket with supplied 
screws.

The left and right Cabinet Brackets are identical. 
The Locking Tab of each Outer-Slide Rail must face towards the rear 
of the cabinet.

Working in the cabinet…

5.

The cabinet must have a set of vertical cabinet rails in the back as well 
as the front.  If there is no set in the back, these must be installed.  The 
back rail is installed the same as the front rail, with the supplied 
screws.

6.

Install each assembled Cabinet Bracket (with attached Outer-Slide 
Rail) to the appropriate side of the cabinet.

The U-shaped cutout of the Cabinet Bracket must face up.

7.

Slide the station (with an Inner-Slide Rails mounted on each side) into 
the Outer-Slide Rails in the cabinet; an audible snap is heard.  Contin-
ue sliding the station in until the station is fully seated.

8.

Secure the station to the cabinet front rails with the supplied screws. 

Note

Note

Summary of Contents for MTR2000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands