manualshive.com logo in svg

Motorola MTR2000, Installation And Operation Manual

Share
Download
Motorola MTR2000 Installation And Operation Manual Download Page 48

Installation

68P81096E37-N

21

06/28/05

Most station configuration parameters are altered through the Radio Service Software (RSS) with the exception of 
some parameters for the following boards, which are configured through jumpers: 

•

4-Wire Wireline Interface Board (CLN1203),

•

4-Wire Euro Wireline Interface Board (CLN1204),

•

Auxiliary I/O Board(CLN1206). 

4-Wire Wireline Interface Board 

Model CLN1203 WIB supports tone control of the station.  CLN1203 pro-
vides a fixed impedance of 600

Ω

 to the wireline.  Figure 6 shows the jump-

er locations for tone control.

.

4-Wire Euro Wireline Interface Board

Figure 7 shows the correct settings of impedance matching jumpers for the 
model CLN1204 WIB, as determined by the country in which the station is 
being operated.  Incorrect jumper settings may violate local telecommuni-
cations authority regulations and place the equipment in an unapproved 
status.  Some countries also specify a maximum allowed line input level.  
Refer to the RSS Online Help, under Line Level. 

3

BOARD CONFIGURATION

C84

T1

T2

C15

C74

P11

P15
P13

P17

P10

P14

P12

P16

P6

P2

Figure 6.        CLN1203 Wireline Interface Board Jumper Settings

P10,

P11

P12,

P13

P14,

P15

P16,

P17

Tone Remote Control

2-wire/4-wire configurations

out

Summary of Contents for MTR2000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands