Motorola MTR2000 Installation And Operation Manual Download Page 47

Page: 47 / 79

Installation

68P81096E37-N

06/28/05

Figure 5. Slide Rail Installation; Option X346AB (Left Side Shown)

Locking Tab

(towards back

of cabinet)

Outer-Slide Rail

Mounting

Hardware sets; (4)

Inner-Slide Rail Mounting

Screws; panhead (2),

station side

Inner-Slide Rail

Outer-Slide

Rail

Note

The left-side slide rail assembly is shown, as
viewed from the front of the cabinet. The left
side is a mirror image of the right side.

Direction

That Station

Slides Out

Station

Mounting

Screws; (2)

Mount Outer-Slide Rails

to Brackets; ONLY use

lower slot of Brackets.

Long Bracket

Short Bracket

Install a cage nut in line with
clearance hole in Threaded Strip
prior to fitting bracket to the front
cabinet rail.
This nut is required for mounting
the station.
The cage nuts are provided with
the cabinet.

Threaded

Strip

Front

Cabinet Rail

Rear

Cabinet Rail

Bracket

Mounting

Screws; (4)

Note: Middle-Slide Rail
not shown (for clarity).

Summary of Contents for MTR2000
















































































Search results

Summary of Contents for MTR2000

Reviews:

Brands by name

Popular brands

Motorola MTR2000, Installation And Operation Manual

Search results

Summary of Contents for MTR2000

Reviews:

Brands by name

Popular brands