manualshive.com logo in svg

Motorola MTR2000, Installation And Operation Manual

Share
Download
Motorola MTR2000 Installation And Operation Manual Download Page 13

68P81096E36-H

06/28/05-UP 

Motorola Inc., 2005
All Rights Reserved
Printed in U.S.A.

1301 E. Algonquin Road, Schaumburg, IL 60196

Government & Enterprise Mobility Solutions

The Motorola MTR2000 Base Station/Repeater provides analog conventional and trunking capabilities in a reli-
able, software-controlled design.  An innovative modular design and microprocessor-controlled Station Control 
Module (SCM) allows for superior station flexibility and simplified system upgrades.

All of the features described in this manual may not be currently supported.  Refer 
to the “Summary of Operating Features” section for a list of standard features, op-
tional features, and planned future features.

Flexible Mechanical Design

All elements of the station are designed for EIA 48.3cm (19") rack mounting, allow-
ing the equipment to be mounted in standard telephone-style equipment racks, or 
various sizes of Motorola cabinets. Figure 1 shows a typical 40W station.
 

1

INTRODUCTION

Note

Figure 1.        MTR2000 Station

DESCRIPTION

Summary of Contents for MTR2000
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands