12A
12B
EN
EN
05. PROGRAMMING
MENU FUNCTIONS
01
• Press the
M
key for 4 seconds to enter the programming menu.
02
• The display will show
P1
and press
▲
and
▼
keys repeatedly until it shows
P6
.
03
• Press the
M
key once to access this submenu.
04
• The display will show a value between 00 and 45, which identifies the thousands of
maneuvers to which the motor will emit a warning maintenance light.
Use the
▲
or
▼
keys to put on the desired option.
05
• Press the M key once to save this option.
06
• The control board will exit to standby mode (--) and the configuration is complete.
Funcionality
• This notice serves to schedule revisions to the automatism, gate or
springs after a certain number of complete maneuvers (open-stop-close-stop). When
the automatismo completes the number of maneuvers defined by this menu, the LEDs
will blink during 2 minutes after every maneuver, to emit the maintenance warning.
01
• Press the
M
key for 4 seconds to enter the programming menu.
02
• The display will show P1 and press
▲
and
▼
keys repeatedly until it shows P7.
03
• Press the M key once to access this submenu.
04
• The display will show the value L0 or L1, which identifies the option in which the
central is configured. Use the
▲
or
▼
keys to put on the desired option.
05
• Press the M key once to save this option.
06
• The control board will exit to standby mode (--) and the configuration is complete.
Funcionality
• This menu allows you to enable or disable the possibility to program a
new transmitter through one already configured (see page 11.A).
L0 means that this functionality is disabled, and
L1
means that is enabled.
• Programming maintenance warnings
• Programming transmitters using already configured
transmitters
05. PROGRAMMING
MENU FUNCTIONS
01
• Press the
M
button for 4 seconds to enter the programming menu.
02
• The display will show
P1
and press
▲
and
▼
keys repeatedly until it shows
P5
.
03
• Press the
M
key once to access this submenu.
04
• The display will show the value
H0
or
H1
, which identifies the option in which the
central is configured. Use the
▲
or
▼
buttons to select the desired option.
05
• Press the
M
key once to save this option.
06
• The control board will exit to standby mode (--) and the configuration is complete.
Functionality
• This function causes the central to ignore all orders for the opening
course sent by configured devices.
• If you press the transmitter during the opening, the order is rejected and it continues
to open
• If you press with the door completely open, it will begin to close.
• If you press during closing, the gate reverses direction and starts to open.
When disabled, you can control the opening or closing of the gate whenever you want,
and their behavior is open-stop-close-stop-open (...) by each time you press the
transmitter.
• Enable/disable function condominium
Note •
The
P4
and
P5
functions, when activated, prevent the gate to stay open. This
way the gate will always open completely, starting the closure after the pause time
defined in
P4
.
Note
• The option
00
disables the maintenance warning. Any other option defines
thousands of operations, the lowest value is 5000 operations (option
05
) and the
maximum is 45000 operations (option
45
).
Whenever you want to reconfigure this option, you must perform two configurations.
First, set the option to
00
to make a RESET to the counting maneuvers. After that, make
a new one setting the new desired option. The central will, from this moment on, start
counting maneuvers to emit the maintenance warning.
01
• Press the
M
key for 4 seconds to enter the programming menu.
02
• The display will show
P1
and press
▲
and
▼
keys repeatedly until it shows
P8
.
03
• Press the
M
key once to access this submenu.
04
• The display will show three numbers, each one for 2 seconds separated by
intervals of 1 second between them.
After this the control board will automatically exit to standby mode (--).
Funcionality
• This function serves only to show all completed maneuvers performed
by the automatism (open-stop-close-stop).
Example:
If when entering the
P8
submenu the display first show nº
15
, then nº
65
and
finally nº
22
, means that a total of
156522
complete maneuvers have already been
done.
RESET
through the menu
P6
: To restart maneuver counting, go to
P6
submenu, and
• Counting maneuvers
